Analog Devices Breaks New Ground For Vital Sign Detection And Portability In Patient Monitoring Medical Equipment

21 2

ADI’s new JFET-input in-amp improves performance and shrinks package size by 50%, increasing channel densities in patient monitors and portable medical electronics.

Analog Devices continues its history of serving the medical electronics industry by introducing the AD8220 JFET-input instrumentation amplifier. The AD8220 enhances the detection of patient vital signs in both fixed-line and transportable electrocardiograms (ECGs), electroencephalograms (EEGs) and other types of patient monitoring devices. Housed in an 8-lead plastic MSOP (mini-small-outline package) that is half the size of competing devices, the AD8220 in-amp allows designers of medical equipment to break new ground by freeing up additional board space to significantly increase ECG and EEG channel density, allowing for smaller medical monitoring systems. Monitoring equipment with high channel density also gives medical professionals more measurement points for very small signals like heart pulses and brain activity while protecting patient vital signs from electrical interference. In addition, the AD8220 operates on a single low-voltage power supply that draws only 700 ВµA, making it ideally suited for use in portable patient monitoring systems.

21 3

The AD8220 features an extremely low input bias current of just 4 pA (pico amps), which is less than half the level of competing components and addresses a significant source of signal error in precision instruments. The AD8220 also achieves an 80 dB common mode rejection ratio (CMRR) up to 10 kHz (G=1), while competing in-amps guarantee only 72 dB to 200 Hz. With significantly lower input bias current and higher CMRR, health care professionals can now measure heart pulses, electrical brain waves, and other patient vital signs at previously undetectable levels. The high CMRR, meanwhile, shields these signals from outside interference by rejecting electrical noise from other parts of the human body.

About the AD8220
With JFET (junction field effect transistor) inputs, the AD8220 in-amp achieves a guaranteed input bias current of 20 pA, maximum, and 4 pA, typical. It specifies a 1-nA input bias current over temperature, and 2 ВµV/В°C input offset voltage temperature drift. The rail-to-rail output of the AD8220 allows designers to improve dynamic range by increasing the gain further before reaching the supply rails. Furthermore, the AD8220’s 80 dB CMRR (G=1) over frequency ensures that only the desired signals are monitored and unwanted common-mode signals are rejected.

The AD8220 is ideally suited for patient monitoring systems, where its small size, low current noise and low input bias current increase the sensitivity and noise rejection of fixed-line and portable medical equipment, such as ECG and EEG systems. The low input bias and high CMRR characteristics also make the AD8220 a fit for industrial automation applications, such as electrometers and other precision instrumentation systems where extremely small currents must be measured in electrically noisy environments.

Fujitsu Laboratories and imec Holst Centre Develop Wireless Transceiver Technology

21 1

Complies with the 400 MHz-band international standard while consuming 1/10th the power of previous models, lightening the burden on patients who use sensors

Fujitsu Laboratories Ltd. and Imec Holst Centre announced that they have developed a wireless transceiver circuit for use in body area networks (BAN) for medical applications that adheres to the 400 MHz-band international standard.

While the subject of high expectations for medical applications, wireless monitoring of brainwaves or other vital signs has in the past required over a dozen milliwatts (mW) of electric power. Now, however, by optimizing the architecture and circuitry, Fujitsu Laboratories and imec Holst Centre have succeeded in reducing the electric power requirements of wireless transceiver front-ends, to just 1.6 mW when receiving data and 1.8 mW when transmitting.

This technology extends by approximately ten-fold the battery life of conventional sensor products used for patient monitoring. This cuts the frequency of battery replacement or recharges, lightens the burden on patients, and increases the work efficiency of medical practitioners.

Based on this joint research into wireless transceiver technology, Fujitsu Laboratories plans to apply it to non-medical uses, as well, such as to the monitoring of societal infrastructure, thereby further enhancing network front-end interface technologies.

Details of this technology were announced at the IEEE International Solid-State Circuits Conference 2014 (ISSCC 2014), which opened February 9 in San Francisco (ISSCC Presentation 9.7)


In the field of healthcare and medicine, BAN have attracted attention for their potential application in collecting patient-monitoring data via a wireless network of sensors placed on the patient’s body (Figure 1). The various sensor nodes that make up the BAN all need battery power, and to make the system as convenient as possible for both the patient and medical practitioners, there is a need to extend battery run-times so the required frequency of battery replacement or recharging is held to a bare minimum.

Technological Issues

The component in the sensor node that draws the most power is the wireless transceiver circuit, so to extend battery life, the power demands of that part need to be reduced. The challenge has been in developing a compact, low-power transceiver that can support the variations in transfer rates which medical systems require, without adding any new circuitry.

About the New Technology

This research project stipulated a 400-MHz wireless specification compliant with IEEE 802.15.6, the international standard for BANs, and support for two independent modes: a 4.5 Mbps high-speed mode capable of transmitting brainwaves, images, and other data needed in medicine, and an 11.7 kbps low-speed, low-power mode for low-power operations when sensor nodes are on standby.

Two points about the new technology are as in the figure below:

1. Digitally controlled receiver technology

Simplifying the architecture of the transceiver circuit as much as possible has resulted in lower power demands. The digitally controlled transceiver circuit uses a programmable structure that can change its circuitry characteristics to support different phase and frequency modulation methods in adherence to BAN international standards. The receiver consists of a low-noise amplifier, mixer, low-pass filter, and AD converter, and uses a direct-conversion technique that extracts the baseband signal directly from the incoming wireless signal. The use of this technique, along with minimized power requirements for all of the constituent circuitry, made it possible to greatly reduce power requirements. The 4.5-Mbps high-speed mode optimizes the frequency characteristics of the low-pass filter and AD converter through digital circuits. In the 11.7-kbps low-speed, low-power mode, the low-noise amplifier operates at lower power, which degrades its sensitivity, but digital processes compensate for this.


2. High-speed digital three-point modulation technology

Using a transmitting mixer in the transmitter makes it easier to implement high-speed mode, but mixers and their driver circuitry are known to greatly increase power demands. A combination of the following three techniques resulted in low-power operation.

  • Rather than using a transmitting mixer, the circuitry uses a digital three-point modulation scheme in which a PLL, which generates the wireless signal from the digital circuit, takes as input high-frequency and low-frequency signals, and, similarly, the amplified transmit signal is input to the power amplifier.
  • To implement the high-speed mode using digital three-point modulation, a dual-varactor circuit technology was developed that, when in high-speed mode, increases the variation in the varactor’s capacitance at the VCO, which takes the high-frequency modulated signal as input.
  • For low-speed/low-power mode, a low-power technology was developed that reduces the VCO modulation circuit’s baseline current by 90% while still allowing modulation.

These technologies support both a low-speed mode and high-speed mode with more than 300 times the transfer rate, resulting in a maximum power consumption of 1.6 mW when receiving and 1.8 mW when transmitting.


This transceiver circuit for healthcare applications has potential applications beyond patient monitoring, and could be used as a sensing front-end interface for medical-device management. In both applications, the lifespan of the batteries used in the sensor nodes will be greatly extended, relieving the burden on patients and making operations more efficient for medical practitioners.

Future Plans

Based on the newly developed wireless transceiver technology, Fujitsu Laboratories plans to extend its application beyond medicine and healthcare, applying it as a fundamental network front-end technology for use in such areas as agriculture and livestock management, monitoring of societal infrastructure and structures, factory monitoring, and environmental monitoring.